Rack Accessories (431 items)

Aluminium blanking plates in various height units. To neatly finish off free locations within the mounting level.

Holds the swing frame in the open position.

Integrated clamping membranes ensure reliable tightening and strain relief to protect the cables.

Made of clear chromated steel strip, 75 mm² cross section, for cable shield contact.

Made of clear chromated steel strip, 75 mm² cross section, for cable shield contact.

To raise the TS roof for ventilation purposes, in three different heights.

To fit: Enclosure type: EB Enclosure type: BG with cam Enclosure type: AE with cam Enclosure type: Based on AE with cam Enclosure type: Wall-mounted enclosure AE with cam Enclosure type: AE with 3-...

Lock inserts for handle systems

Lock inserts for handle systems

For reduction from 24 to 10 poles

For using connectors with varying numbers of poles. - For reduction from 24 to 6 poles

With welded-on transparent pouch and self-adhesive backing.

For affixing to the inside surfaces of doors.

For affixing to the inside surfaces of doors.

For fastening to the perforated door strip and/or affixing to the door.

For fastening to the perforated door strip and/or affixing to the door.

For fastening to the perforated door strip and/or affixing to the door.

To fit: Enclosure type: AE with stainless steel cam Enclosure type: Based on AE with stainless steel cam Enclosure type: One-piece console - stainless steel console cover

To fit: Enclosure type: AE with stainless steel cam Enclosure type: Based on AE with stainless steel cam Enclosure type: One-piece console - stainless steel console cover

Lock cylinder inserts for cam locks.

Enclosure, case and lock systems are supplied as standard with matching keys

For ventilation by convection; easily retro-fitted using 4 screws.

For ventilation by convection; easily retro-fitted using 4 screws.

With pre-punched holes for cable glands. Use seal for standard gland plates.

Simply knock out the holes for the cable glands using a screwdriver.

As spare/replacement part for the standard gland plates supplied loose.

Simply pierce the plastic with a sharp object, and pull through the cable.

Trim panels at the front and rear with fitted corner pieces and side trim panels.

For mounting on TS, SE and PC enclosures, for easier floor cleaning and to compensate for floor irregularities ±15 mm. Height 100 mm.

For clip-on mounting onto the cover plate, contact hazard protection.

PTC heater without fan, continuous thermal output 10 - 150 W, with quick-connection terminal.

PTC heater without fan, continuous thermal output 10 - 150 W, with quick-connection terminal.

PTC heater without fan, continuous thermal output 10 - 150 W, with quick-connection terminal.

PTC heater with fan, continuous thermal output 235 - 800 W, and quick-connect terminal.

PTC heater with fan, continuous thermal output 235 - 800 W, and quick-connect terminal.

PTC heater with fan, continuous thermal output 235 - 800 W, and quick-connect terminal.

Temperature-dependent speed control for TopTherm fan-and-filter units and air/air heat exchangers for noise reduction and to save energy in part-load operation. - For mounting on a 35 mm support ra...

For fan-and-filter units/outlet filters. Easy cleaning thanks to exterior silicone coating approved for use with foodstuffs.

The quick-change frame is more than just an alternate frame. Together with the seal, the lower part of the frame is screw-fastened to the enclosure. In this way, it is possible to install and remov...

Rack-mounted fan with integral speed control and fault evaluation. Mounting directly on the 482.6 mm (19") level.

Guide frame for Vario rack-mounted fan: Installation directly in the subrack, via two mounting brackets on the 482.6 mm (19") mounting angles.

Guide frame for Vario rack-mounted fan: Installation directly in the subrack, via two mounting brackets on the 482.6 mm (19") mounting angles.

For mounting on the horizontal and vertical enclosure sections of a TS via additional assembly components.

With LED connection cable or with LED connection cable

Für schwere Einbauten. Besonders geeignet zum Einbau von Stütz-Isolatoren.

Zur schwenkbaren Befestigung des Tragarmsystems an vertikalen Flächen. Abnehmbare Abdeckung für einfache Kabeldurchführung.

Designed to accommodate both DC and AC components, pull-out component front for optimum access to the wiring space from above and below.

For screw-fastening into the enclosure base. Width across flats 17, mounting thread multi-tooth 30.

For retrospective levelling on uneven floors at the installation site up to a maximum of 15 mm. Installed through the base/plinth corner piece. A door offset caused by uneven flooring can be correc...

For heavy assemblies up to 5000 N per support rail.