Industrial PCs (319 items)

Wago 750-404

The counter acquires 24V binary pulses and transports the counter status to the installed bus system. Counting is enabled and inhibited via the GATE input. Digital outputs DO 1 and DO 2 can be set ...

The counter acquires 24V binary pulses over a defined time period (gate time) and transports the counter status to the installed bus system. The U/D input allows either Up or Down counting. Digital...

The counter is used for frequency measurement here, with the pulse period of the 24V signal being measured at the CLOCK input and then converted to a frequency value. Measurement is enabled and inh...

The counter acquires 24V binary pulses and transports the counter status to the installed bus system. The U/D input allows either Up or Down counting. Digital outputs DO 1 and DO 2 can be activated...

The I/O module is equipped with two 16-bit up counters. The CLOCK 1 and CLOCK 2 inputs acquire 24V binary pulses and transmit the counter status to the installed bus system. Digital outputs DO 1 an...

This output module modulates a 16-bit information in the pulse width. The field side is electrically isolated from the bus system. The pulse duty factor is given by a 16-bit value. The outputs are ...

This output module modulates a 16-bit information in the frequency. The field side is electrically isolated from the bus system. The frequency is given by a 10-bit value with a resolution of 2 Hz/d...

After the fieldbus node is assembled with the correct buscoupler and I/O modules, the end module is snapped onto the assembly. It completes the internal data circuit and ensures correct data flow.

The supply module provides the I/O modules with the corresponding supply potential. The maximum current at the supply module is 10A. When configuring the system, it must be ensured that this total ...

Field side connection module for multiple tapping of the supply voltage. This eliminates the need for additional terminal blocks.

The field side connection module provides 0 V potential for the outputs of the 8-channel output module 750-530. This eliminates the need for additional terminal blocks. The 24V supply and 0V potent...

The supply module provides the I/O modules with the corresponding supply potential. The maximum current at the supply module is 6.3A. When configuring the system, it must be ensured that this total...

The separation module visually divides a fieldbus node into sections. Separation module 750-616/030-000 has no power jumper contacts.

Distance Module The separation module visually divides a fieldbus node into sections. Separation module 750-621 has power jumper contacts that can supply the power to adjacent bus modules.

Binary Spacer Module Binary spacer modules reserve bit addresses in the process image of a fieldbus node. The operating mode as well as the bit width can be adjusted by DIP switches on the side of ...

Power Supply; 24 V/5 … 15 VDC The I/O module generates 5V, 8V, 10V, 12V and 15V DC output voltages from the 24VDC input voltage. The output voltage is selected by a DIP switch located on the side o...

Bus Extension End Module The end module for the internal data bus extension 750-627 is attached to the end of the I/O terminal block like the standard end module 750-600. The block is terminated wi...

Bus Extension Coupler Module The coupler module for the internal data bus extension module 750-628 replaces the fieldbus coupler/controller at an I/O terminal block. It is also the mating piece for...

This module is an SSI interface for the direct connection to an SSI transmitter. After the interface has given a clock pulse to the sensor, the interface reads the incoming data and transmits it di...

SSI transmitter interface; Fail-safe 2 channel analog input; 125 kHz; Binary code This module is an SSI interface for the direct connection to an SSI transmitter. After the interface has given a cl...

This module is an SSI interface for the direct connection to an SSI transmitter. After the interface has given a clock pulse to the sensor, the interface reads the incoming data and transmits it di...

This module is an SSI interface for the direct connection to an SSI transmitter. After the interface has given a clock pulse to the sensor, the interface reads the incoming data and transmits it di...

SSI transmitter interface; 25 bits; 125 kHz; Gray code This module is an SSI interface for the direct connection to an SSI transmitter. After the interface has given a clock pulse to the sensor, th...

SSI transmitter interface; 13 bits; 250 kHz; Binary code This module is an SSI interface for the direct connection to an SSI transmitter. After the interface has given a clock pulse to the sensor, ...

This module is an SSI interface for the direct connection to an SSI transmitter. After the interface has given a clock pulse to the sensor, the interface reads the incoming data and transmits it di...

SSI transmitter interface; 13 bits; 125 kHz; Gray code This module is an SSI interface for the direct connection to an SSI transmitter. After the interface has given a clock pulse to the sensor, th...

The digital impulse interface is designed for the connection of magnetostrictive distance measurement sensors with a start/stop interface. After receiving a read pulse, these sensors deliver a time...

Incremental encoder interface; RS-422; 32 bits This module is an interface for incremental encoders with standard connections (e.g., RS-422, differential, single-ended). A counter with quadrature d...